Cigarette lighter jack, turn on from the button

Why can’t I plug car gadgets into the cigarette lighter?

If the above recommendations about not plugging powerful devices directly into the cigarette lighter still were not taken into account, and it stopped working, then in this case the following small guide on how to fix such a malfunction will help.

If the electrical socket in the car has refused to work, then most likely its fuse has blown. That’s why you should check the part with the smoking cigarette symbol or the word “sigar” on it before jumping to any other conclusions. It can be located in absolutely different places at cars: in a trunk, under a cowl, in a niche of driver’s feet, in a glove compartment, under a torpedo and so on. In any case, this part can definitely be found in the location of the relay and fuse box.

Video on how to replace the cigarette lighter fuse:

So, if the fuse is really blown, replacing it is the main (and only) step where the repair of the cigarette lighter ends. Since the device will work properly again from this point on.

When self-repairing the electric socket in the car, you should remember that it is undesirable to put a more powerful fuse, because instead of it next time the socket itself may burn out. Then the situation will be saved only by complete replacement of the cigarette lighter. It is also not recommended to insert into the socket of the device various low-quality plugs that are loose, loose in the socket, not very tightly assembled, and so on. This can lead to a short circuit and, again, lead to the need to completely replace the device.

If the fuse turned out to be intact, then the matter takes a different turn

In this case, it is necessary to get to the cigarette lighter from the inside, and to do this, you need to try a little effort and carefully disassemble the console, under which it is located. Next, you need to check the condition of the fusible element

It will probably be spoiled and broken. Here it is desirable to replace it, but if there is no new element at hand, you can do with a wire of the same diameter.

At the market of auto parts now you can even find a self-restoring fusible link. Its operating principle is to disconnect the connection at overheating and to reconnect it at cooling down.

So you can see that in the question of why the cigarette lighter does not work, there are two reasons and they require a different approach.

In the case of not self-repair, but the appeal to the car service, the specialists will quickly determine the cause and eliminate it. This method is the highest quality among the possible options, but also the most expensive at that. Complete replacement of the cigarette lighter at the service station is also possible. In any case it is a quick-fix breakdown, and not so critical. But at the same time bringing certain inconveniences to the driver and requiring correction.

car cigarette lighter where is plus where is minus

Electrical Equipment VAZ 2110 2111 2112 cigarette lighter VAZ 2110 2111 2112

In a car cigarette lighter, the center contact is plus, the shell is minus. Forumchame, who can remind you where the plus and minus on the cigarette lighter. CBR “Human Friends” Mobile Car Cigarette Lighter. REXANT car charger in the cigarette lighter USB 5V 1A “mini” white 18-. H6 lamp pinout – drom ru; Led car lamp h6 102smd buy. All you need to do is connect just two wires plus and minus. from the cigarette lighter to the autocompressor how to determine where the plus, where the minus. “Cigarette lighter,” in automotive slang, can mean two things:. and connect the plus of the cigarette lighter to it, the minus to the body and the third wire,. 11.69 – Motorcycle/Car Cigarette Lighter Special Modification Harness. into the cigarette lighter plus or minus two antenna and then the other end 2 min – Uploaded by niov73Creating a car cigarette lighter plug from improvised means. Cigarette lighter doesn’t work – do it yourself, fast! The charger is long, the cigarette lighter should reach, hence the marriage… Are you sure that your charger does not care where its plus and minus. Diagrams for connecting a car stereo, explanations and recommendations… car stereo, the connection of the plus wire from the cigarette lighter. It can be connected to the body of the car (to the mass), or better to the minus. Can anyone know where what should be: plus on top, minus. Accidentally broke the wire that plugs into the cigarette lighter. The backbone of any car refrigerator is a semiconductor plate. to federal public roads by vehicles. from minus 40 C to plus 55 C. 93% at plus 40 C. People tell me – well I shorted the plus to the minus fuse does not … often Chinese car adapters for the cigarette lighter. Cigarette lighter for the car: connect the devices. Look at the cigarette lighter base: the pin is the plus, the ring is the minus. Nowadays, the car cigarette lighter can be considered an indispensable thing. you need to know where in the cigarette lighter is the plus and where the minus . compufreer.com, 0, 0, -, 0, -, 15, 0, Car cigarette lighter plus minus . “Plus” should be connected after the fuses, “ground” should be connected under. that if you connect the “plus” of the stereo to the “plus” of the cigarette lighter, and the “minus” to the. In order to prevent car thieves from “stealing”. With every day of available mods.

READ

Noise and vibration isolation of Chevrolet Captiva.

Disadvantages[ | ]

The cigarette lighter can not be called sufficiently reliable electrical connection. Its very design did not allow for long and reliable switching of large currents. Reliable fixation of the consumer plug in the cigarette lighter jack can be provided by an increased number of clamping legs, but so far there is no uniform standard for such a connection. In practice, however, non-standard plugs usually have:

a) A spring-loaded center contact (“plus”), which may be a slightly longer fuse extending outward, in case the plug contains, for example, an electronic voltage regulator for powering appliances sensitive to power quality parameters. Such a fuse can be replaced by unscrewing the plastic ring that holds it in place and connects the halves of the plug body.

b) Two clamping legs of the ground (“ground” or “minus”), one of which may not have any electrical contact at all inside the plug, including with the second, working, leg. That is, in simple terms, one of the pins may not be engaged, in which case the current does not conduct through itself.

A specific example of a device with the properties described in both paragraphs above could be the car adapter that comes with the IconBIT (Funktech) FTB 16000S Universal Portable Battery for charging the latter from the cigarette lighter.

In the socket, the site of the central contact can be located deep or can be close. The grooves for the clamping pins (even if they are present) may not be located where they are located on the plug. The cross-section of the contacts themselves are not sufficient for switching large currents. Due to the various vibrations and shocks while driving, the reliable contact between the plug and the cigarette lighter jack is lost, the connection sparks, the possibility of a short circuit is not excluded. In addition, in today’s cars are used simultaneously a large number of connected devices: navigators, video recorders, chargers for small batteries, televisions, radios. For this purpose, various tees and splitters are used, which by themselves can not add reliability.

READ

Car talker with my own hands

The impossibility of a sharp transition to a connection with greater reliability is explained by the fact that the cigarette lighter in the form in which it is now, is the de facto standard in cars and its trouble-free operation can be guaranteed only when you use it for its intended purpose – to warm up the coil insert.

Cigarette lighter replacement

Is it true that charging through a car cigarette lighter kills batteries

How to put a new cigarette lighter in the car, if the old one burned out and cannot be repaired? Let’s take VAZ 2108 car with low dashboard (old model) as an example.

Buy a new auto cigarette lighter.
Using a flat screwdriver, remove the plastic tips from the air damper control levers.
Remove the self-tapping screws securing the air damper control bracket.
Pull toward you to remove the knob from the fan speed control.
Remove the self-tapping screws fixing the center console to the instrument panel (2 on each side). Pull the console toward you and disconnect its connectors from the wiring harness.
Remove the console.
Using two fingers, push the bracket holding the light bulb holder to the sides and remove it from the socket light guide.
Use your fingers or a screwdriver to push the plastic socket retainers in and pull the assembly housing out of the console opening.
Insert a new socket in place of the old one.
Install the illumination assembly on the light guide. Make sure that there is contact between the backlight bracket and the housing.
Connect the console connectors to the wiring harness.
Check that the buttons, regulator, and the assembly you replaced are working.
Put the console back in place.
Attach the flap control bracket to it.
Secure the console with self-tapping screws.
Slide the knobs onto the levers and adjuster axle.

❶ How to install the cigarette lighter

The car comes with a cigarette lighter as basic equipment, and it would seem that if you’re a non-smoking motorist, the device is completely unnecessary. If while driving a need to charge your cell phone battery or turn on the fan, laptop? This will help cigarette lighter. And the socket of this design plays the role of an ordinary household socket in the car. But, like any technique, the car tends to accumulate dirt and dust, and the cigarette lighter socket is bound to get clogged.

READ

Installing an extra battery in the trunk with your own hands.

Remove the cassette frame by prying around its perimeter with a flat-blade screwdriver. Open the ashtray and unscrew the self-tapping screws that secure the ashtray. Remove the ashtray and disconnect the wiring from the car battery terminals. Remove the trim on the floor tunnel as well. Remove the spigot from the cigarette lighter, then remove the light bulb from the socket and the back cover. Remove the cigarette lighter from the housing – ring by prying it off with a screwdriver, then remove the backlight ring. Press the lamp screen so that the tabs of the screen show through the slot in the cigarette lighter’s light guide, and remove it. Press the screwdriver on the cigarette lighter socket retainer so that it loses its grip on the light guide. Push the socket outward from the trim and then remove it from the trim by dragging the wiring harness through the hole.

Check the heating time of the cigarette lighter coil, it should be strictly 20 seconds. After that the cigarette lighter cartridge should click into place. If this time is longer or shorter than 20 seconds, adjust the cigarette lighter by bending or unbending the appropriate contacts.

Squeeze the plastic tabs on the light guide and slide it out of the trim. Install the cigarette lighter in reverse order.

How to Install the Cigarette Lighter

How to connect the cigarette lighter

Car inverter 12 220v – how to choose the converter

Needless to say, how necessary the cigarette lighter is in the car – and this, for the most part, has nothing to do with smoking. The whole point is that the cigarette lighter socket serves as a power source for many electrical appliances, when there is no possibility to connect them to the main socket.

What appliances can be plugged into the cigarette lighter:

Cell phone and tablet charger,
video recorder,
navigation device,
radar detector,
vacuum cleaner,
refrigerator,
heated seats,
maybe a walkie-talkie,
On old VAZ cars – car radio, etc.

The convenience of cigarette lighter is undeniable, but there is a disadvantage: you must constantly keep under control the total power of all devices connected to the device – it must not be more than 120 watts, the current should not exceed 10 amps.

The more intense the current, the more reliable should be the contacts of the cigarette lighter, which loosen from the jolts and shocks during the trip. As a consequence, there is a short circuit and a fire in the car. Various adapters and splitters, which allow you to connect to the cigarette lighter a few electric devices, and thus significantly increase the load on it, do not add to the reliability of the device.

How to connect the cigarette lighter: the sequence of work

The process of connecting the cigarette lighter begins with the preparation of the necessary tools: it is a file or file, soldering iron, screwdriver and pliers.

To begin with, remove the cigarette lighter and disassemble it;
Remove the semiconductor plate, it often prevents the normal operation of the device;
Saw off the protrusion on the body of the cigarette lighter with a file;
Reassemble the cigarette lighter;
First you need to strip the wires with which it is connected, and crimp them to the terminals. Do not reverse the polarity!
Dismantle the center console; Sometimes you may additionally need to remove the armrest and armrest cover to unscrew the self-tapping screws;
Remove the backlight wires, and then the entire unit;
Now connect the wires, fixing them with connecting clips. Connection of wires is made according to this scheme: brown wire connects to the backlight wire, black and yellow wires – to the cigarette lighter wire. Don’t forget to insulate each connection;
Pull the wires down to connect to the cigarette lighter connector;
Place the cigarette lighter in its seat, in reverse order. Push its ring through first, then the cup itself. If necessary, adjust the diameter of the ring to the diameter of the hole, with a file;
Put the light in place.

READ

Door noise vibration isolation with your hands

This completes the installation of the cigarette lighter, it remains to check its work.

How to use the cigarette lighter properly so it will last a long time?

The most important thing is to add the power of all electrical appliances that are simultaneously connected to the cigarette lighter through the splitter.

Disconnect all appliances from the cigarette lighter in time. Keep in mind that even if the engine is turned off and the devices are still connected to the cigarette lighter, they are still running and therefore gradually drain the car battery.

Video: How to install an extra cigarette lighter in the VAZ 2115

Video: Replacing the cigarette lighter VAZ 2110, 2111, 2112

Cigarette lighter jack, turn on from the button

Hello all! I came to the need to install the splitter, because before every trip I had to insert and at the end of the trip to pull the plug recorder from the cigarette lighter jack. The previous owner of the car did the same thing, and apparently because of that now my cigarette lighter is so loose that before pulling the plug, the jack had to be held by hand, otherwise it would come out. This caused some discomfort and I had to think of something to avoid pulling the plug back and forth every time).

And the more so because I had the splitter for a long time, from my wife’s old car, and it was lying idle at home.

The plug was broken a long time ago and was glued to it. I took it off and soldered two wires instead of the plug.

I decided to power the cigarette lighter splitter from the constant plus through the button, and connect the recorder to it. The button – the recorder works, pressed again – it turned off. I also had the button, now I need to think where to connect it.

When installing a Euro brake, left a place from the old button. I closed it with a regular plug of the window handle from 2108. But I had the same cringe to put something there). I took this plug, and barbarically implanted a button in it.

I did not have to think much about the place for the splitter. The choice fell on the shelf under the glove compartment. I drilled a hole for the wires with a self-tapping screw.

I put the wires under the panel by removing the side panel.

I put on the wires for the button, the button is convenient in terms of connection, no chips, terminal blocks on the bolts.

READ

How to change the antifreeze in the car with your own hands?

Cigarette lighter jack, turn on from the button

And the more so because I had the splitter for a long time, from my wife’s old car, and it was lying idle at home.

The plug was broken a long time ago and was glued to it. I took it off and soldered two wires instead of the plug.

I did not have to think much about the place for the splitter. The choice fell on the shelf under the glove compartment. I drilled a hole for the wires with a self-tapping screw.

I put the wires under the panel by removing the side panel.

I put on the wires for the button, the button is convenient in terms of connection, no chips, terminal blocks on the bolts.

Button put on the minus, according to this scheme.

I took the constant plus from the battery from the power wire of the radio.

put a fuse in the circuit, so there would be no short circuit

took the minus from this bolt

Sorry about the quality, I did not notice when I took photos

And the splitter itself glued to the shelf with double-sided adhesive tape

Now you do not need to yank the plug registrar back and forth in the cigarette lighter, enough to press the button. Plus it is possible to simultaneously charge the phone with the working registrar, before you had to turn it off. The built-in cigarette lighter is free, everything is neatly hidden and there are no wires hanging in front of your nose)

From the ignition did not connect the recorder, because sometimes I leave it on when parked. For example, on parking lots near shopping malls. And there are different situations when you need to turn the recorder on without ignition or leave it on. Clicking the button does not bother you too much. The button feels great in place of the old emergency switch.

I always remember to turn it on and off, as the button is in full view and always in front of my nose. I do not remember if there were such a topic or not, so I decided to share, just in case it will be useful to someone.